DSC PK5590CL Installationsanleitung Seite 2

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 2
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 1
Figure 3 Mounting Hole Template
FCC Compliance Statement
Caution: Changes or modifications not expressly approved by Digital Security Controls could void your authority
to use this equipment.
This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance
with the manufacturers instructions, may cause interference to radio and television reception. It has been type tested and
found to comply with the limits for Class B device in accordance with the specifications in Subpart “B” of Part 15 of
FCC Rules, which are designed to provide reasonable protection against such interference in any residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
interference to television or radio reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Re-orient the receiving antenna
• Relocate the alarm control with respect to the receiver
• Move the alarm control away from the receiver
• Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet prepared by the FCC helpful: “How to Identify and Resolve Radio/Television
Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402,
Stock # 004-000-00345-4.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Limited Warranty
Digital Security Controls warrants that for a period of 12 months from the date of purchase, the product shall be free
of defects in materials and workmanship under normal use and that in fulfilment of any breach of such warranty,
Digital Security Controls shall, at its option, repair or replace the defective equipment upon return of the equipment
to its repair depot. This warranty applies only to defects in parts and workmanship and not to damage incurred in
shipping or handling, or damage due to causes beyond the control of Digital Security Controls such as lightning,
excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper applica-
tion of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warran-
ties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls.
Digital Security Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its
behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this prod-
uct.
In no event shall Digital Security Controls be liable for any direct, indirect or consequential damages, loss of antici-
pated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or
operation or failure of this product.
Warning: Digital Security Controls recommends that the entire system be completely tested on a regular basis. However,
despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this
product to fail to perform as expected.
Important Information:Changes or modifications not expressly approved by Digital Security Controls could void the
user’s authority to operate this equipment.
©DSC 2007 Printed in Canada
4.0” (10 cm)
Ensure cut out is 1.5 inches (4 cm)
minimum from nearest stud to enable
correct operation of drywall fasteners
NOTE:
Drill 4 holes in the positions indicated
using a 3/8 (9.5mm) drill bit
Mounting Hole Template
29007282R003
Seitenansicht 1
1 2

Kommentare zu diesen Handbüchern

Keine Kommentare