DSC WLS900 Spezifikationen PDF herunterladen

Mounting the Detector

Once you have found a location that is within range of

the receiver, you can mount the WLS912L.

1. Remove the mounting plate from the detector.

2. At the selected mounting location, place the

mounting plate on the wall (with the tab facing

down, or to the right), or on the ceiling. Mark the

screw locations. Wall anchors should be used for

all screw locations.

3. Secure the backplate to the wall.

4. Slide the detector onto its backplate.

5. Repeat the installation test using the AFT–100

tester to confirm proper operation.

FCC Compliance Statement

CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use

this equipment.

This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the

manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply

with the limits for Class B device in accordance with the specifications in Subpart “B” of Part 15 of FCC Rules, which are designed

to provide reasonable protection against such interference in any residential installation. However, there is no guarantee that inter-

ference will not occur in a particular installation. If this equipment does cause interference to television or radio reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

• Re-orient the receiving antenna

• Relocate the alarm control with respect to the receiver

• Move the alarm control away from the receiver

• Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user

may find the following booklet prepared by the FCC helpful: “How to Identify and Resolve Radio/Television Interference Prob-

lems”. This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402, Stock # 004-000-00345-4.

Limited Warranty

Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shall be free of defects

in material and workmanship under normal use and that in fulfilment of any breach of such warranty, Digital Security Controls Ltd.

shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies

only to defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond control

of Digital Security Controls Ltd. such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse,

alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether express

or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd. This warranty contains the entire war-

ranty. Digital Security Controls Ltd. neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf

to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential damages, loss of anticipated profits,

loss of time or any other losses incurred by the buyer in connection with the purchase, installation or operation or failure of this product.

WLS912L

Glassbreak Detector

Available Models: WLS912L-433, WLS912L-900

Installation Instructions

The WLS912L is a battery-operated glassbreak sensor, designed to detect the sound

produced by the shattering of framed glass. Equipped with an RF transmitter, the

WLS912L establishes a supervised, one–way communications link with the system

controller. The WLS912L uses Dynamic Signal Processing* to provide accurate

detection of plate, laminated, wired and tempered glass types, while rejecting com-

mon false alarm sounds.

*Protected under US Patent 5,675,320

Specifications

Operating Voltage: 3.0V (two 3V Lithium batteries)

Operating Temperature: 0

C - 50

C (32

F - 122

Operating Humidity: 5% – 95% RH, non-condensing

Maximum detection range

Compatible control units/receivers: (P)NT9010-433, P(C)5132-433 or Envoy

Battery Guidelines and Installation

• Use fresh batteries. Most batteries have a “best before” date printed on their

packaging or on the batteries themselves. Buy batteries that have a “best

before” date of two years or more from your purchase date

• When disposing of used batteries, follow the instructions and precautions

printed on the batteries. Many cities and communities have collection sites or

services for used household batteries. Contact your municipal offices for

information on the disposal of used batteries

• Do not mix old and new batteries

• Dispose of any batteries promptly, keep away from children

NOTE: Use only Energizer Lithium EL123AP, Tekcell CR123A or Panasonic

CR123A lithium batteries. Use of any other battery may present a risk of fire or

explosion.

CAUTION: The cell used in this device may cause a fire or chemical burn hazard if

mistreated. Do not recharge, disassemble, heat above 100°C

(212°F) or incinerate.

To install batteries:

1. Remove the detector from its mounting plate:

If unmounted, hold the detector by its sides and push down on

the top end of the mount-

ing plate, as shown at

right.

If mounted, press the

detector in the direction

shown below.

Glass Type Thickness Minimum Glass

Size (L X W)

Level 1

Setting

Level 2

Setting

Plate/

Tempered

1/8" – 1/4"

3 – 6mm

12" X 12"

30cm X 30cm

20ft

10ft

Wired/

Laminated

1/4"

6mm

18"X18"

46cmX46cm

20ft

DO NOT USE

Toronto, Canada • www.dsc.com

Technical Help Desk (Canada & US): 1-800-387-3630

Printed in Canada 29005723 R005

1 2

Inhaltsverzeichnis

Seite 1 - Glassbreak Detector

Mounting the DetectorOnce you have found a location that is within range ofthe receiver, you can mount the WLS912L. 1. Remove the mounting plate from

Seite 2 - Enrolling the WLS912L

2. Install the batteries positive (+) side first, with the correct polarity, as shown below. Setting the Dip SwitchesThe detector has user-selectable

Weitere Dokumente für Sicherheitszugriffskontrollsysteme DSC WLS900

Um das Dokument anzuzeigen DSC WLS900 Spezifikationen

DSC WLS900 Spezifikationen (4 Seiten)

Um das Dokument anzuzeigen DSC WLS900 Betriebsanleitung

DSC WLS900 Betriebsanleitung (52 Seiten)

Um das Dokument anzuzeigen DSC WLS900 Bedienungsanleitung

DSC WLS900 Bedienungsanleitung (4 Seiten)

Um das Dokument anzuzeigen DSC WLS900 Bedienungshandbuch

DSC WLS900 Bedienungshandbuch (28 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC WLS900 Spezifikationen

Stöbern Sie online oder laden Sie Spezifikationen nach Sicherheitszugriffskontrollsysteme DSC WLS900 herunter. DSC WLS900 Specifications Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Sicherheitszugriffskontrollsysteme DSC WLS900

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC WLS900