DSC Digital Security Control PC158O Technical Information PDF herunterladen (Seite 1)

INTRODUCTION

Section 1

The LINKS2450 transmits alarm system information over a long-range radio

network. It may be used with the following DSC alarm control panels:

• PC1580 v1.0 • PC5010 v1.0 and up • PC4010/4020 v3.x

• PC1565 v2.x and up • PC5015 v2.2 • PC5008 v2.x and up

• PC585 v2.x and up

This manual will describe how to install and program the LINKS2450 for connection

to the above panels.

1.1 Specifications

NOTE: If the panel uses automatic SIA or Contact ID communications formats, the

reporting codes the LINKS2450 will send must still be programmed on the panel.

• Power supply: 11.5-14VDC at 750mA (PS1520, PC5204, PC4204, or powered

from Bell+/Aux- control panel terminals)

• Radio transmitter frequency: range from 440 to 470MHz

• Communication Buffer: 80 Events

• Transmission Range: Approximately 16 Kilometers (10 Miles)

• Cabinet dimensions: 4.17” high × 5.75” wide × 1” deep (104mm × 146mm ×

26mm); color: white

• Module supervision via the alarm control panel

• Protected against static and lightning induced transients

• Programming by keypad or downloading software. The LINKS2450 is complete

with a default program and is operational with a minimum of programming.

• To program via a keypad when connected to PC5015, PC5010, PC5008, PC1580,

PC1565 or PC585 panels, program the LINKS2450 using any system keypad

• To program via a keypad when connected to PC4010/4020 v3.0 panels,

program the LINKS2450 using a PC2550RK keypad connected directly to the

LINKS2450.

• EEPROM Memory

The LINKS2450 uses EEPROM memory, which will retain all program

information even if AC and battery power, are removed.

1.2 Antenna

NOTE: You must match the antennas to the frequency you will be using.

The antenna for the LINKS2450 is

not

supplied. For optimum performance of the

LINKS2450, use a quality antenna system, such as model SLA-532, available from

Safe Link Corporation. This 5/8 over 5/8 wave high performance antenna offers

features specifically designed for security radio installations.

• 5db gain two-piece mast with center coil

• Standard frequency range 440-470MHz

• Five feet of coax with BNC connector attached.

Normally, you will install the antenna on the top of the alarm control panel cabinet.

For better reception at the central station, you can mount the antenna in a remote

location using the optional mounting bracket. A compact 13” replacement mast,

model SLA-313 (3dB gain) is available for limited space installations.

1 2 3 4 5 6 ... 19 20

Inhaltsverzeichnis

Seite 1 - INTRODUCTION

1INTRODUCTIONSection 1The LINKS2450 transmits alarm system information over a long-range radionetwork. It may be used with the following DSC alarm con

Seite 2 - INSTALLING THE LINKS2450

10Special procedures are necessary to activate this feature for a radio account.Check with Safe Link for more information.Program the amount of time i

Seite 3 - DC, 1A power supply

11TESTING THE LINKS2450 Section 5Before testing the LINKS2450, ensure that the control panel is correctly pro-grammed and operating properly. Refer to

Seite 4 - PC1580, PC585 Panels

12RESET LINKS2450 PROGRAMMING TO FACTORYDEFAULT Section 6If you need to reset the LINKS2450 to factory default programming, follow thedirections in th

Seite 5 - DIAGRAM 2-2

13PROGRAMMING WORKSHEETS[01] Module ConfigurationDefault Option ON OFFON I_______I1Communications Communicationsenabled disabledOFFI_______I2Serial co

Seite 6 - PROGRAMMING THE LINKS2450

14[82] Miscellaneous Restoral Reporting Codes (PC1580 panelonly)Default = FFI_______I_______I General Zone Fault RestoreI_______I_______I General Syst

Seite 7 - Diagram 3-1

LIMITED WARRANTYSafe Link Ltd. warrants that for a period of twelve months from the date of purchase, theproduct shall be free from defects in materia

Seite 8

Seite 9 - Option 2

INSTALLATION MANUALVersion 1.0• W A R N I N G •Please refer to the System Installation Manual for information onlimitations regarding product use and

Seite 10 - PC5008 v2.0 panels only)

FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd.could void your authority to use th

Seite 11 - 5.4 Testing Tools

TABLE OF CONTENTSiSection 1: Introduction 11.1 Specifications ...

Seite 12 - DEFAULT Section 6

2INSTALLING THE LINKS2450Section 2Before installing the LINKS2450, install and test the security system to which it willbe connected, according to the

Seite 13 - PROGRAMMING WORKSHEETS

NOTES:ii

Seite 14 - Default

32.4 Mount and Wire the LINKS24501. Run the panel wiring and the power supply wiring to the LINKS2450mounting location.2. Remove the four screws that

Seite 15 - LIMITED WARRANTY

4DIAGRAM 2-1Hook-up For PC5010, PC5015, PC5008, PC1565,PC1580, PC585 PanelsNOTE: Programming section [01], option 2 must be OFF for LINKS2450 to workw

5DIAGRAM 2-2Hook-up for PC4010/4020 v3.0 PanelsNOTE: Programming section [01], option 2 must be ON for LINKS2450 to work withthese panels.CAUTION: Due

Seite 17 - INSTALLATION MANUAL

6PROGRAMMING THE LINKS2450Section 3See section 3.1 for programming instructions when connecting the LINKS2450 toa PC5015, PC5010, PC5008, PC1580, PC15

Seite 18 - Notice to the user:

73.2 Programming a LINKS2450 for Use with a PC4010/PC4020v3.0 or higher panel.There are two stages in programming the LINKS2450 for a PC4010 or PC4020

Seite 19 - TABLE OF CONTENTS

8Program the LINKS2450 Toggle Options on the PanelAt a PC4010 or PC4020 system keypad, enter reference # [000405] and [*], or scrollto the “LINKS2XXX”

Seite 20

9PROGRAMMING DESCRIPTIONS SECTION 4[01] Module ConfigurationOption 1: Communications Enabled / DisabledEnable this option to have the LINKS2450 initia