DSC PC15OO Installationshandbuch PDF herunterladen (Seite 21)

[26] Downloading Telephone Number

This telephone number is used by the panel to call the

downloading computer when a request to call is make by

entering [

∗

][4] or for an auto-download. See Section [14]

3rd System Option Code, lights 2 and 3. See Section [01] 1st

Phone Number for instructions on programming the

downloading telephone number.

[27] Downloading Access Code

This 4-digit code allows the panel to confirm that it is

communicating with a valid downloading computer. Enter 4

digits using the numbers 0 through 9 only. The factory default

code is [1515].

[28] Panel Identification Code

This 4-digit code allows the downloading computer to confirm

the identity of the control panel. Enter 4 digits using the

number keys 0 through 9 only. The factory default code is

[1501].

[29] For Future Use

[30] Reset to Factory Default

Software

Entering [30] will perform a software reset to the factory

default values. Once this command is entered, the keypad

buzzer will beep several times. The “Trouble” LED will be ON

during the reset sequence.

Hardware

If the installer’s code is forgotten and a software reset cannot

be performed, the panel can be reset to the factory default

values with the following method.

1. Remove all power, AC and battery, from the panel.

2. Short the pads on the panel labelled EEPROM RESET.

3. While maintaining the short, power-up the panel and

wait for at least 10 seconds before removing the short.

4. Upon removal of the short, the keypad buzzer will beep

and the panel will be reset to the factory default values.

[31] 4th System Option Code

Use the same programming method as in Section [12].

ZONE

LIGHT

[1] • OFF =

For future use

[2] • OFF =

For future use

[3] • OFF =

For future use

[4] ON = Show bypass status while armed or disarmed

• OFF = Show bypass status while disarmed only

[5] ON = Set for AC = 50 Hz

• OFF = Set for AC = 60 Hz

[6] ON = Restore on bell time-out (if zone is restored)

• OFF = Restore as follower (when zone restores)

• Factory default

[32] 5th System Option Code

Use the same programming method as in Section [12].

ZONE

LIGHT

[1] ON = Loss of AC will not cause an AC trouble

• OFF = Loss of AC will cause AC trouble

[2] ON = No bell during Auto-Arm (burst every 10

seconds is silenced)

• OFF = 1 burst of bell / siren every 10 seconds

during Auto-Arm pre-alert

[3] • ON = Home-Away zones will have an entry

delay when tripped

OFF = Home-Away zones act as interior when

tripped

[4] ON = Quick-Exit is enabled ([

∗

][0] ignores

1 transition of a delay zone)

• OFF = Quick-Exit is disabled

[5] ON = Auxiliary delay zones can be force armed

• OFF = Auxiliary delay zones cannot be force armed

[6] • ON = Standard Fire – Fire alarms will pulse bell

OFF = Temporal Fire – Fire alarms will sound bell

using the temporal fire pattern

Temporal fire pattern:

0.5 sec. ON, 0.5 sec. OFF,

0.5 sec. ON, 1.5 sec. OFF.

• Factory default

[33] For Future Use

[34] 6th System Option Code

Use the same programming method as in Section [12].

ZONE

LIGHT

[1] ON = Audible Exit Delay with urgency

• OFF = Standard Exit Delay

[2] ON = Bell Squawk during Exit Delay

• OFF = No Bell Squawk during Exit Delay

[3] ON = Audible Exit Fault enabled

• OFF = Audible Exit Fault disabled

[4] ON = Urgency applied to Entry Delay

• OFF = Standard Entry Delay

[5] ON = Bell Squawk during Entry Delay

• OFF = No Bell Squawk during Entry Delay

[6] ON = [F] Key disabled

• OFF = [F] Key enabled

• Factory default

When Light 3 is ON (Audible Exit Fault): When the

system is armed and a Standard Delay Zone is left open

at the end of the Exit Delay, the bell/siren will sound a

steady tone for the duration of the Entry Delay.

Entry and Exit Delay Urgency: When the urgency

option is selected for the audible Entry Delay, the keypad

will sound a constant tone during the Entry Delay. During

the last 10 seconds of the Entry Delay, the keypad will

sound a pulsing tone to warn that the delay is about to

expire.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 35 36

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC PC15OO Installationshandbuch Seite 21

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC PC15OO