DSC PC3OOO Installationshandbuch PDF herunterladen (Seite 16)

PRINTER SETUP

The PC3000 with version 7.0 or higher software is capable

of sending data to a local printer.

The printer must be capable of serial communication (RS-

232).

The PC3000 should work with most serial printers, however

the printers on the following list are strongly recommended.

Compatible printers:

1. Brother M-1109

2. Brother M-1809

3. Star DP 40

4. Epson EP 40

5. C - Itoh model 8510 B

6. Citizen 120-D with serial card

7. Citizen 180-D with serial card

8. Rolland DG PR 1112 with serial card

9. Panasonic KX P1091 I with serial card

10.Mannesman Tally MT81 with serial card

Configuring the Printer

1.Serial interface

2.Baud rate = 2400 (other baud rates may be used but

section [49] must be changed accordingly)

3.Parity = None

4.Character length = 8 bits

5.Auto linefeed = Off

6.American/Canadian character set

To hook up the printer, start by fully powering down the

panel

and the printer. Using A DB-25 connector, connect the

printer

to the panel as shown below. The maximum cable length

should be 6 feet.

Note: If SRTS is not available turn on light 7 in section

[49] and attach yellow to 4 (RTS) or to 20 (DTR).

Programming the Panel for Use with a

Printer

Section [49] in the panel must be programmed to enable the

printer function. See section [49], page 23. Power up the

panel and program it as described below.

Enter the Installer’s Programming section and edit the

following sections. ([Q]+[8]+[Installer’s Code])

Section Printer Only Monitored and Printer

[01] Do not program Program normally

[02] Program normally Program normally

[03] Do not program Program (see section

[49] zone light 6)

[04] Do not program Program normally

[05] to [15], [45], Program everything

Program everything

[50], [53] and [54] you wish printedyou

wish printed

[16] to [18] Program normally Program normally

[19] Light 4 must be off Light 4 must be off

[20] to [27] Program normally Program normally

[28] Program with “0C” Program with “0C”

[29] to [32] Program normally Program normally

[33] Program all 1's Program normally

[43] to [48] Program normally Program normally

[49] Printer setup Printer setup

[50] to [54] Program normally Program normally

Note: the time of day, day, month and year must be

programmed into the panel using the

[Q]+[6]+[Master Code]+[1] command as described on

page 10.

Plug in the printer, insert paper and turn it on line. Your

serial printer is now ready to use.

The following is a sample of a printout from the serial

printer:

07:33 04\01\91 STATION 2 ACC. # 5678

CLOSING ACCESS 1

12:57 04\01\91 STATION 1 ACC. # 1234

ALARM ZONE 2

ALARM ZONE 12

13:01 04\01\91 STATION 1 ACC. # 1234

RESTORE ZONE 2

RESTORE ZONE 12

18:01 04\01\91 STATION 2 ACC. # 5678

OPENING AFTER ALARM

OPENING ACCESS 1

Notes:

Station 0 is for a local only printer.

Station 1 is telephone number 1.

Station 2 is telephone number 2.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 43 44

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC PC3OOO Installationshandbuch Seite 16

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC PC3OOO