NOTE: Waterflow zones always require single EOL

resistors regardless of any other programming. Refer

to the wiring diagram or Section 2.9 “Zone Wiring”

for zone configuration.

Fire Supervisory (11)

A Fire Supervisory zone monitors fire critical systems to

indicate when those systems are in a condition that could

prevent normal operation. This zone will indicate an

“Off-Normal Supervisory” condition when a short cir-

cuit is detected. When the zone is open, a zone trouble

will be indicated and the keypad will beep.

24 Hour Zones (Types 12-24)

These zones are always active. When violated, they will

create an alarm, whether the partition is armed or dis-

armed.

For Types 16-21: When violated, the panel will immedi-

ately latch the bell outputs and will communicate to the

central station. Each zone has a different SIA identifier.

• 24 Hr Bell (12): This zone, when violated, will activate

the burglary outputs.

• 24 Hr Bell/Buzzer (13): This zone, when violated, will

create an alarm whether the partition is armed or dis-

armed. However, if the panel is armed, it will activate

the burglary outputs; if disarmed it will activate the

keypad buzzer.

• 24 Hr Buzzer (14): This zone, when violated, will acti-

vate the keypad buzzer.

• 24 Hr Technical (15): This zone is silent.

• 24 Hr Gas (16): This zone is audible.

• 24 Hr Heat (17): This zone is pulsed audible.

• 24 Hr Medical (18): This zone is silent.

• 24 Hr Emergency (19): This zone is audible.

• 24 Hr Water (20): This zone is audible.

• 24 Hr Freeze (21): This zone is audible.

• 24 Hr Holdup (22): This zone is silent. It does not acti-

vate Burglary outputs or the Latched Strobe output.

• 24 Hr Panic (23): This zone is silent. It does not activate

Burglary outputs or the Latched Strobe output.

Latching 24 Hr (24)

When violated, this zone will operate the same as the 24

hour bell zone (12) with one exception: the installer’s

mode ([*][8]) must be entered before the system can be

armed. The keypad display will read “Arming Inhibited

Call for Service.” This is to ensure that the problem will

be examined by the installer.

Momentary Arm (25)

A momentary closure of this zone will alternately arm

and disarm the partition. This zone can be used with a

keyswitch to arm and disarm the system.

NOTE: This zone type must not be used as a global

zone. If a keyswitch zone has been tampered or

faulted, the zone must be restored before it can be

used to arm or disarm the system.

Maintained Arm (26)

When this zone is closed, the partition will disarm. When

this zone is violated, the partition will be armed. This

zone can be used with a keyswitch to arm and disarm the

system.

NOTE: This zone type must not be used as a global

zone. If a keyswitch zone has been tampered or

faulted, the zone must be restored before it can be

used to arm or disarm the system.

Forced Answer (27)

When this zone is tripped, the panel will instantly pick

up the telephone lines to search for a downloading com-

puter. Do not use this zone type to monitor for alarms.

LINKS Sup (28)

The LINKS Supervisory zone is used with a LINKS mod-

ule to monitor for LINKS troubles. When the LINKS

PGM output activates, a LINKS trouble will be logged on

the event buffer and the zone trouble will be transmitted.

NOTE: LINKS Supervisory zones always require single

EOL resistors regardless of any other programming.

Refer to the wiring diagram or Section 2.6 “Special-

ized Zone Wiring” for zone configuration.

LINKS Answer (29)

The panel can be uploaded/downloaded via the cellular

network. If the LINKS1000 detects an incoming call, it

will activate an output which can be used to violate this

zone type, forcing the panel to answer the cellular call

and begin communicating with the downloading com-

puter.

NOTE: LINKS Answer zones always require single EOL

resistors regardless of any other programming. Refer

to the wiring diagram or Section 2.5 “Zone Wiring”

for zone configuration.

Zone Attributes

The following is a description of each zone option. Scroll

through each option and press [*] to toggle between on

and off. When all necessary changes are made, press [#]

to return to the previous menu.

Each zone type has different attributes enabled by

default. For a list of these default settings, see the PC4010

Programming Worksheets.

• Bell Audible – This will determine whether the zone

will activate bell outputs and PGM outputs pro-

grammed to sound fire/burglary alarms when an

alarm occurs. Select [Y] for audible, [N] for silent.

• Bell Pulsed – This will determine how the bell outputs

and PGM outputs programmed to sound fire/burglary

alarms will sound for an alarm. Select [Y] for pulsed,

[N] for steady.

• Bypass Enable – This will allow the zone to be manu-

ally bypassed. Select [Y] to allow bypassing by the

user, [N] to prevent it. This attribute should not be

enabled for Fire zones.

• Chime Function – If the door chime option is enabled,

keypad will chime both when the zone is violated and

restored. Select [Y] for chime, [N] for no chime. To acti-

vate/deactivate the Door Chime feature for a partition,

enter [*][4] at a keypad.

• Force Arm – When force arming is enabled, the parti-

tion(s) the zone is assigned to can be armed even if the

zone is not secure. The zone will be temporarily

bypassed and will be added back into the system if it is

later restored. Select [Y] to enable this feature. If [N] is

selected, the zone must be secured or manually

bypassed before arming will be allowed.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 51 52

Kommentare zu diesen Handbüchern

Keine Kommentare

Whirlpool PCN 752 T/IX/HAR Handbücher

Bedienungsanleitungen und Benutzerhandbücher für Kamine Whirlpool PCN 752 T/IX/HAR.
Wir stellen 1 PDF-Handbücher Whirlpool PCN 752 T/IX/HAR zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung

Whirlpool PCN 752 T/IX/HAR Bedienungsanleitung (8 Seiten)

Marke: Whirlpool | Kategorie: Fireplaces | Größe: 1.25 MB |

Inhaltsverzeichnis

CONSIGNES DE SÉCURITÉ

INSTALLATION

RACCORDEMENT AU GAZ

DESCRIPTION DU PRODUIT

USAGE QUOTIDIEN

NETTOYAGE ET ENTRETIEN

GUIDE DE DÉPANNAGE

SERVICE APRÈSVENTE

Weitere Produkte und Handbücher für Kamine Whirlpool

Modelle	Dokumententyp
PGS 300/NB	Bedienungsanleitung Whirlpool PGS 300/NB Instruction for Use, 4 Seiten
AKS 400/IX	Bedienungsanleitung Whirlpool AKS 400/IX Instruction for Use, 8 Seiten
FTGHL 751 D/IX/A LPG	Bedienungsanleitung Whirlpool FTGHL 751 D/IX/A LPG Instruction for Use, 8 Seiten
THP 642 W/IX/I RU	Bedienungsanleitung Whirlpool THP 642 W/IX/I RU Instruction for Use, 8 Seiten
PGS 300/WH	Bedienungsanleitung Whirlpool PGS 300/IX Instruction for Use [pt] , 4 Seiten
THP 642 IX/I	Bedienungsanleitung Whirlpool THP 642 IX/I Instruction for Use, 8 Seiten
GA3 124 C WH A	Gebrauchs- und Pflegehandbuch Whirlpool GA3 124 C IX A Health and safety, 9 Seiten
THP 752 IX/I	Bedienungsanleitung Whirlpool THP 752 IX/I Instruction for Use, 8 Seiten
ACM 808/BA/WH	Bedienungsanleitung Whirlpool ACM 808/BA/WH Instruction for Use [es] [fr] [it] [pt] , 4 Seiten
KHMF 9010/I	Bedienungsanleitung Whirlpool KHMF 9010/I Instruction for Use, 20 Seiten
GOR 6414/NB	Bedienungsanleitung Whirlpool GOR 6414/NB Instruction for Use, 7 Seiten
KHMS 9010/I	Bedienungsanleitung Whirlpool KHMS 9010/I Instruction for Use [da] , 20 Seiten
GOA 9523/WH	Bedienungsanleitung Whirlpool GOA 9523/WH Instruction for Use, 7 Seiten
GA2 124 IX HA	Gebrauchs- und Pflegehandbuch Whirlpool GA2 124 IX HA Health and safety, 9 Seiten
GA3 124 IX HA	Gebrauchs- und Pflegehandbuch Whirlpool GA3 124 IX HA Health and safety, 9 Seiten
FTGHL 641 D/IX/A LPG	Bedienungsanleitung Whirlpool FTGHL 641 D/IX/A LPG Instruction for Use [en] , 8 Seiten
AKR 3500/IX	Bedienungsanleitung Whirlpool AKR 3700/IX Instruction for Use, 4 Seiten
TQG 641 A(BK)	Bedienungsanleitung Whirlpool TQG 641 A(BK) Instruction for Use, 10 Seiten
PGE 300/IX	Bedienungsanleitung Whirlpool PGE 300/NB Instruction for Use [de] [en] [fr] [nl] [pl] [sk] , 4 Seiten
TI 622 W FRA	Bedienungsanleitung Whirlpool TI 622 A FRA Instruction for Use [tr] , 26 Seiten

DSC MAXSYS PC4010 Installationshandbuch Seite 20

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC MAXSYS PC4010

Whirlpool PCN 752 T/IX/HAR Handbücher

Whirlpool PCN 752 T/IX/HAR Bedienungsanleitung (8 Seiten)

Inhaltsverzeichnis

Weitere Produkte und Handbücher für Kamine Whirlpool