DSC SYSTEM MASTER PC4000 Bedienerhandbuch PDF herunterladen (Seite 6)

QUICK ARM

[✱]+[0]

Entering [✱][0] is accepted as a valid arming code when the “Quick Arm” feature is

activated. This command is often used when individuals are required to arm the

system but not disarm it. This could be used with home visitors in the case of a

residential alarm or junior employees and maintenance staff in the case of a

commercial alarm. See instructions in the “[✱][6] Users Programming Commands”

section for activating the “Quick Arm” feature. Users with a one-time use access code

should not use this feature, because the one-time use code is only erased when it is

used to arm the system.

QUICK EXIT

[✱]+[0] WHEN ARMED

Entering [✱][0] when the system is fully armed will allow the user 2 minutes to exit the

premises through any delay zone without altering the status of the system if the “Quick

Exit” feature is enabled. After [✱][0] is entered into an armed system, one and only one

delay loop may be tripped. Any additional activity on any other active loop will cause

that loop to begin its alarm sequence. Quick exit activation will be logged onto the

event buffer.

FIRE SAFETY IN THE HOME

Most fires occur in the home and to minimize this danger it is recommended that a

household fire safety audit be conducted and a family escape plan be developed.

HOUSEHOLD FIRE SAFETY AUDIT

1. Are all electrical appliances and outlets in a safe condition e.g. frayed cords,

over-loaded lighting circuits? If you are uncertain about the condition of your

electrical appliances or household service, have a professional evaluation.

2. Are all flammable liquids stored safely in closed containers in a well ventilated

cool area? Cleaning with flammable liquids should be avoided.

3. Are fire hazardous materials (matches) well out of reach of children?

4. Are furnaces and wood burning appliances properly installed, clean and in good

working order? Have a professional evaluation.

ARMING

Close all protected doors and windows and stop movement in areas covered by

motion detectors.

The “Enter Code to Arm System” message should be on the LCD display. The

system cannot be armed unless the “Enter Code to Arm System” or “Secure System

or Enter Code...” message is displayed.

Enter a [4 Digit Security Code]. As each digit is entered the keypad will beep.

■

If the security code was entered incorrectly, the keypad will beep steadily for 2

seconds.

■

If the code was entered correctly but the system was not secure due to an open

zone, the keypad will beep quickly followed by a steady tone.

■

When the correct code is entered, the “Exit delay in Progress” message will be

displayed and the keypad will beep three times quickly. If a System Master Code

was entered, the system master menu will appear. See “System Master Codes”.

A timer will appear in the right side of the display indicating the remaining time in the

exit delay. Exit the premises through the designated exit-entry door. At the end of the

allowed exit time the message on the keypad will change to “Enter Code to Disarm

System”.

DISARMING

Enter the premises through the designated exit-entry door. The keypad buzzer will be

on. Go to the keypad and enter the [4 digit security code]. If an error is made in

entering the code, press the [#] key and enter the code again. The “Armed” light will

go out and the keypad buzzer will stop. The correct security code must be entered

before the allowed entry time expires. If an alarm occurred while the panel was

armed, the “View Memory” message will be on the display with the zone name for the

zone that caused the alarm. The display will keep those messages on for two minutes

or until the [#] key is pressed to return the panel to the normal arm-disarm mode.

AUTO-BYPASS/HOME-AWAY ARMING

If a correct security code is entered and you do not exit the premises through a

designated exit-entry door, the system will, at the end of the Exit delay time, arm with

interior zones automatically bypassed if those interior zones have been programmed

as “Home-away” zones. These zones will remain bypassed until a delay zone is

tripped or [✱][1] is entered to reactivate bypassed home-away zones.

This is a convenience feature for someone who wishes to remain on the premises

with the system armed. That person does not have to manually bypass the home-

away zones.

To reactivate the Home-away zones that have been automatically bypassed, press

[✱][1]. This command is a quick method of fully arming the system in residential

applications before going to bed.

1 2 3 4 5 6 7 8 9 10 11 ... 19 20

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC SYSTEM MASTER PC4000 Bedienerhandbuch Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC SYSTEM MASTER PC4000