DSC SYSTEM MASTER PC4000 Bedienerhandbuch PDF herunterladen (Seite 7)

VIEW PARTITIONS

[✱]+[6]+[ACCESS CODE]+[8]

This function will allow the user to view the status of other partitions that their

access code has been enabled for in the access code partition mask. The

partition mask is programmed in the [✱][5] User Programming commands, when

programming the user access codes. For example, if an access code has been

enabled in the partition mask for partitions 1, 2 and 5, they can only view the

status of these partitions.

To view the partitions status, press the [<] or [>] key to toggle through the

partitions. The partition labels will be displayed along with a letter to the far right.

The letter shows the status of that partition.

A means the partition is Armed,

R means the partition is secure and Ready to be armed, and

N means Not ready to be armed because zones are not secure.

This function must be enabled by the installer for the user to be able to enter this

section. If the installer does not enable this section, you will hear an error tone

when selecting this section.

INSTALLERS’ PROGRAMMING COMMANDS

[✱]+[8]+[INSTALLER’S CODE]

This command is used by the installer to program the PC4000.

“AT-HOME” ARMING

[✱]+[9]+[ACCESS CODE]

Entering [✱][9] before the arming code, arms the panel without any entry delay on

the delay zones and bypasses zones that are defined as “Home-away”. This

command is used for arming the system while at home. Once the panel is Armed

in this mode, using [✱][1] will remove the bypass from those zones defined as

“Home-away” if they have NOT been manually bypassed. The [✱][1] command,

as used here, only removes the bypass from zones that were automatically

bypassed with the [✱][9] command.

ZONE BYPASSING

[✱]+[1]

A bypassed zone will not cause an alarm. If a zone is bypassed the panel may be

armed even if the zone is open. Use zone bypassing when access is needed to

part of the protected area. Also, damaged wiring or contacts on a zone may be

temporarily bypassed until repairs can be made so that the panel can be armed.

To bypass zones, enter [✱][1]. An access code may be required if the installer has

enabled that option. A menu will appear.

[0] Bypass Zones - This selection takes you immediately to bypassing zones. Use

the [<][>] to select the zones to be bypassed and press the [✱] key to select the

zone. A “✱” will appear beside the zone label to indicate the zone will be bypassed

when the partition is armed.

A zone search routine allows the user to find the desired zone to bypass by entering

in the first letter of the zone to search for, and pressing one of the [<][>] keys. The [<]

key will search for the first zone on the partition that begins with the letter selected.

The [>] key will search for the last zone on the partition that begins with the letter

selected.

The letters of the alphabet have been divided up among the 1-9 number keys on the

keypad.

1 2 3

ABC DEF GHI

4 5 6

JKL MNO PQR

7 8 9

STU VWX YZ

[1] Clear Bypasses - Removes all bypasses from all the zones in your partition and

then takes you to bypassing zones. None of the zones will have a “✱” beside them.

[2] Recall Bypasses - Selecting this will bypass all the same zones that were

selected the last time zones were bypassed. This is for users that are always

bypassing the same zones.

[3] Previous Menu - takes you back to the “Enter Code to Arm System”.

When the PC4000 is programmed, the ability to bypass certain zones may have been

eliminated by the installer. In this case, the “✱” message for those zones will not come

on in response to the bypass command. Zone bypasses are automatically cancelled

when the panel is disarmed.

NOTE

: At no time can any armed zone be bypassed.

While the system is disarmed, bypassing can be used to temporarily silence the

door chime feature on a zone. Simply bypass the zone that the door chime feature

enabled. The keypad will no longer beep when the zone is opened. Be sure to clear

all bypasses before arming, to ensure no zones are unintentionally bypassed.

1 2 3 4 5 6 7 8 9 10 11 12 ... 19 20

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC SYSTEM MASTER PC4000 Bedienerhandbuch Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC SYSTEM MASTER PC4000