DSC PC5020 Installationshandbuch PDF herunterladen (Seite 20)

Keypad Commands: 4.4 Function Keys

options. Use the arrow keys (<>) to scroll to the desired back-

light level and press the [#] key to exit.

• Contrast Control: When this option is selected the keypad

will allow you to scroll through 10 different contrast level

options. Use the arrow keys (<>) to scroll to the desired con-

trast level and press the [#] key to exit.

• Keypad Buzzer Control: When this option is selected the

keypad will allow you to scroll through 21 different keypad

sounder tone options. Use the arrow keys (<>) to scroll to the

desired keypad beeper level and press the [#] key to exit. This

function can be achieved on LED keypads by holding the [*]

key.

[*] [7] Command Output Functions

There are four output functions available to the user. Entering [*]

[7] [1-4] [Access Code, if required] will activate any output pro-

grammed for options [19]-[22] (respectively). Each function can

be performed when the system is either armed or disarmed.

For more information regarding these output types, see section

5.12

“Programmable Outputs”

on page 27.

[*] [8] Installer Programming

Enter [*][8] followed by the Installer Code to enter Installer Pro-

gramming (see Section 3:

“How to Program”

on page 11).

[*] [9] Arming Without Entry Delay

When a partition is armed with the [*][9] command the panel

will remove the entry delay from the partition. After the exit

delay, Delay 1 and Delay 2 type zones will be instant and Stay/

Away zones will remain bypassed. (see section 5.1

“Zone Defini-

tions”

on page 20).

For more information regarding this feature, see the Power864

Instruction Manual.

The entry delay can be activated or deactivated at any time while

the system is armed by pressing [*][9].

NOTE:

Global Delay zones will always have an entry delay,

even if the system is armed using [*][9].

[*] [0] Quick Arm

If the Quick Arm Enable option is enabled the panel can be

armed by entering [*][0]. This is a useful method of arming a Par-

tition when someone without a access code will be required to

arm a Partition.

NOTE:

The Quick Arm feature must be enabled in order for

the Stay/Away function keys to operate as intended. If the

feature is not enabled, the user will be required to enter

their access code after pressing the Stay or Away function

key in order to arm the system in the stay or away mode.

[*] [0] Quick Exit

Quick Exit will allow someone to leave an armed premise through

a Delay type zone without having to disarm and rearm the sys-

tem.

When [*][0] is entered, if the Quick Exit Enabled option is

enabled, the panel will provide a two minute window to exit.

During this time the panel will ignore the first activation of a

Delay type zone. When the Delay zone is secured the panel will

end the two minute time period.

If a second Delay zone is tripped, or if the zone is not restored

after two minutes, the panel will start entry delay.

NOTE:

If Quick Exit is used on a partitioned system, Keypad

Blanking and Access Code Required to Remove Blanking

should be enabled.

Quick Arm Enable . . . . . . . . . . . . . . . .Section [015], Option [4]

Quick Exit Enable. . . . . . . . . . . . . . . . .Section [015], Option [3]

4.4 Function Keys

There are five function keys on the PC5020 keypads labelled Stay,

Away, Chime, Reset and Exit. The operation of these keys is

described below. The function is activated by pressing and hold-

ing the key for 2 seconds.

“Stay” - Stay Arm

Arms the partition to which the keypad is assigned. All Stay/

Away type zones will be automatically bypassed. Delay type

zones will provide entry and exit delay. The Quick Arm feature

must be enabled for this key to function (Section [015], Option

[4]). If Quick Arming is not enabled, the user must enter their

access code after pressing the function key in order to arm the

system in the Stay mode.

“Away” - Away Arm

Arms the partition to which the keypad is assigned. All Stay/

Away type zones will be active at the end of the exit delay. Delay

type zones will provide entry and exit delay. The Quick Arm fea-

ture must be enabled for this key to function (Section [015],

option [4]). If Quick Arming is not enabled, the user must enter

their access code after pressing the function key in order to arm

the system in the Away mode.

“Chime” - Door Chime On/Off

Pressing the key will toggle the Door Chime feature ON or OFF.

One solid beep means the feature has been disabled, three short

beeps means it has been enabled.

“Reset” - Reset Smoke Detectors

Pressing this key will cause the panel to activate for 5 seconds

any output programmed as Sensor Reset. (see section

“[*] [7]

Command Output Functions”

on page 17).

“Exit” - Activate Quick Exit

Pressing this key will cause the panel to activate the Quick Exit

feature (see section

“[*] [0] Quick Exit”

on page 17).

Function Key Options

The programming of any function key on any keypad may be

changed to one of the options listed below. (See section 2.6

“Keypad Assignment”

on page 8 for instructions on changing

function key programming.)

[00] - Null Key

The key is not used and will perform no function when pressed.

[01] - Select Partition 1

Provides an easy way to select Partition 1. This is the same as

pressing and holding the [#] key then pressing and holding the

[1] key to select Partition 1 (see section 4.5

“Global and Partition

Keypad Operation”

on page 19).

[02] - Select Partition 2

Provides an easy way to select Partition 2. This is the same as

pressing and holding the [#] key then pressing and holding the

[2] key to select Partition 2 (see section 4.5

“Global and Partition

Keypad Operation”

on page 19).

[03] - Stay Arm

Same as described in Function Keys - Section 3.5.

[04] - Away Arm

Same as described in Function Keys - Section 3.5.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 42 43

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC PC5020 Installationshandbuch Seite 20

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC PC5020