DSC Power608 Spezifikationen PDF herunterladen (Seite 24)

P R O G R A M D E S C R I P T I O N S

If you have selected the Land Line Test Transmis-

sion in Minutes option, do not program the test

transmission cycle to be less than 10 minutes.

The LINKS Test Transmission can only be pro-

grammed in days.

If the test transmission cycle being programmed is of a lesser

value than the previous value, the system will wait the original

period before the next test transmission is sent, and then begin

reporting with the new interval.

The panel can also send a test for the LINKS 1000 Cellular

Communicator, if being used. If the LINKS 1000 Test

Transmission Code is programmed, the panel will send a

cellular test at the interval programmed in the LINKS Test

Transmission Cycle.

The end user can generate a communicator test. If the System

Test Reporting Code is programmed, the panel will send the

signal when the System Test keypad command is entered (see

Section 3.4 – “[✱] Commands; [✱] [6] User Functions”).

Test Transmission Reporting Codes ................. Section [352]

Test Transmission Time of Day ......................... Section [371]

Test Transmission Cycles .................................. Section [370]

Land Line Test Transmission M/D .............. Section [702]: [3]

5.15 Transmission Delay

If the transmission delay zone attribute is selected for a given

zone, the panel will delay reporting an alarm for that zone for the

number of seconds programmed for the Transmission Delay

Time. If the panel is disarmed before the delay time expires, the

panel will not report the event.

Transmission Delay Time .................................. Section [370]

5.16 Fire, Auxiliary and Panic Keys

The emergency keys are available on all keypads. These keys

must be pressed and held for two seconds before they will

activate. This two second delay is designed to help prevent

accidental activation.

If the [F] / Key option is enabled, when the Fire keys are

pressed and held for two seconds, the panel will activate the

alarm output following the option programmed in section [013]:

[8] (see section 5.13 “Siren”). The alarm output will sound until

a code is entered or until the bell cut-off time expires.

Communication of the signal to central station is immediate.

If the [A] / Key is pressed and held for two seconds, the panel

will sound the keypad beeps three times to verify activation. The

panel will beep the keypad ten times rapidly when a kissoff is

received, to verify communication to the central station.

If the [P] /

Key is pressed and held for two seconds, the

panel will immediately communicate the signal to central station.

If [P] Key Audible Bell and Buzzer option is enabled, the panel

will beep the keypad three times upon activation and activate

the alarm output until a code is entered or the bell cut-off

expires. Otherwise the alarm will be completely silent.

Each LCD keypad may be programmed to have the [F], [A], &

[P] keys enabled or disabled. Please refer to Appendix B

“Programming LCD Keypads”.

The Fire, Auxiliary, Panic keys will operate even if

Keypad Blanking is active (See Section 5.22

“Keypad Blanking”).

[F] Key Enable ............................................ Section [015]: [1]

[P] Key Audible Bell and Buzzer ............... Section [015]: [2]

5.17 Arming/Disarming Options

If the Quick Arm option is enabled, the panel can be armed

without an access code by entering [✱]

[0] or by pressing the

Stay or Away function key.

The Quick Exit option, if enabled, will allow someone to leave

an armed premises through a Delay type zone without having

to disarm and re-arm the system. See Section 3.4 “[✱]

Commands”.

If the Arm/Disarm Bell Squawk option is enabled, the panel will

squawk the alarm output once upon arming and twice upon

disarming. If an alarm is in memory, when the panel is disarmed

the bell will sound three pairs of disarm squawks.

The Opening After Alarm Keypad Ringback option will cause

the keypad to beep 10 times rapidly after the Opening After

Alarm reporting code has been successfully transmitted to the

central station. The Opening After Alarm Bell Ringback option

will cause the panel to squawk the bell 10 times rapidly after the

Opening After Alarm reporting code has been successfully

transmitted to the central station.

If the panel is armed using the Stay function key,

or by entering [

✱✱

✱

][9][access code], there will be

no bell squawks during entry and exit delays,

except for the arm/disarm bell squawks.

Closing Confirmation, if enabled, will cause the keypad to

beep 10 times rapidly after the closing Reporting Code has

been successfully transmitted to central station.

If the Bypass Status Displayed While Armed option is chosen,

the Bypass light will be ON while the system is armed to indicate

that there are bypassed zones.

If the AC/DC Inhibit Arming option is enabled, the panel will not

arm if there is an AC or DC (battery) trouble present on the

system. Arming will not be allowed until the AC or battery trouble

is cleared. If no AC or battery trouble is currently present, when

a user attempts to arm the system, the panel will do an automatic

battery test of the main panel and modules that support a

backup battery. If the battery is good, the system will arm. If the

battery is bad, the system will not arm.

If the AC/DC Inhibit Arming option is disabled, the panel will

not do an automatic battery test when arming is attempted and

the user will

not

be prevented from arming the system when

there is an AC or battery trouble.

If Unidentified Wireless Key Disarming is disabled, the disarm

button will not work on wireless keys which have not been

assigned access codes. (Please see your PC5132 manual for

more information on programming wireless keys.)

This option must be enabled when using a

PC5132 v2.1 or earlier.

Quick Arm Enable ...................................... Section [015]: [4]

Quick Exit Enable ....................................... Section [015]: [3]

Arm/Disarm Bell Squawk ........................... Section [014]: [1]

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 51 52

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC Power608 Spezifikationen Seite 24

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC Power608