DSC PC6010 Installationshandbuch PDF herunterladen (Seite 7)

SYSTEM AREASYSTEM AREA

SYSTEM AREA

SYSTEM OPTIONSSYSTEM OPTIONS

SYSTEM OPTIONS

SYSTEM TIMESSYSTEM TIMES

SYSTEM TIMES

Keypad Lockout Options

This section contains programming for the keypad and reader lockout features. After a programmed

number of incorrect attempts to enter an access or installer’s code, the keypad will lock users out.

This prevents users from performing any system function. A message “Keypad Lockout is Active” will

be displayed for the lockout duration. Keypad lockout is automatically enabled on all system

keypads. See “READER LOCKOUT” under “System Options” to enable the keypad lockout feature

on PC6820 readers.

Enter the number of incorrect code entries (from 000 to 255) required to activate keypad lockout.

The default setting is 005.

This section determines the number of minutes the keypad lockout will be active. Enter the duration

of the keypad lockout. Valid entries are from 000 to 255. The default setting is 015.

System Times

These times apply to the whole system.

Program the amount of time (from 000 to 255 minutes) the bell output will activate for when an

alarm occurs. The factory default setting is 004 (4 minutes). Bell Cutoff is for any output (Bell, SW

Aux or PGM) that is programmed for Fire and Burg, Inv Fire and Burg, Burg Only, Inv Burg Only, Fire

Only, Inv Fire Only, and Tamper.

Program the amount of time (from 000-255 seconds) that a TLM Trouble will be delayed before it is

annunciated on the trouble group. The default is 060.

Program the amount of time (000-255 minutes) before an AC Trouble will be annunciated on the

trouble group. The default is 060.

Program the time (000-255 minutes) before the keypad will display an AC trouble in the fault list.

This will delay the “Trouble Group” annunciation and the “AC Fail TX Delay”. This delay does not

apply to the keypad Power light. If there is an AC trouble, the Power light on the keypad will turn off

immediately. The default is 000 minutes.

Program the time (000-255 minutes) before a “Combus Low PWR” trouble will occur. The default is

000 minutes.

Program the time (000-255 minutes) before a TLM trouble will be logged and displayed in the fault

list. The default is 000 minutes.

Program the amount of time (000 - 255 Minutes) before a Police Code Alarm reporting code will be

sent to the central station. A Police Code Alarm is sent when 2 zone alarms occur within the

programmed time. Default is 060 minutes.

Program the time in minutes that automatic arming can be delayed. Users can delay automatic

arming on assigned areas from a system keypad, or an PC6820 reader with a POST input. When the

programmed delay time expires, automatic arming will begin again. Users may delay automatic

arming as many times as desired. To delay automatic arming at a system keypad, users must enter

their access code, and then follow the available choices displayed on the keypad. To delay automatic

arming at an PC6820 reader, users must first pass an access card through the reader, and then

activate the POST input. The default delay is 030 minutes.

KYPD LOCKOUT OPTKYPD LOCKOUT OPT

KYPD LOCKOUT OPT

(1)(1)

(1)

TOTAL BAD CODESTOTAL BAD CODES

TOTAL BAD CODES

(0)(0)

(0)

LOCKOUT DURATIONLOCKOUT DURATION

LOCKOUT DURATION

(1)(1)

(1)

SYSTEM TIMESSYSTEM TIMES

SYSTEM TIMES

(2)(2)

(2)

BELL CUTOFFBELL CUTOFF

BELL CUTOFF

(00)(00)

(00)

TLM DELAYTLM DELAY

TLM DELAY

(01)(01)

(01)

AC FAIL DELAYAC FAIL DELAY

AC FAIL DELAY

(02)(02)

(02)

AC DELAYAC DELAY

AC DELAY

(03)(03)

(03)

LOW COMBUS DELAYLOW COMBUS DELAY

LOW COMBUS DELAY

(04)(04)

(04)

TLM TROUB. DELAYTLM TROUB. DELAY

TLM TROUB. DELAY

(05)(05)

(05)

POLICE CODE TIMEPOLICE CODE TIME

POLICE CODE TIME

(06)(06)

(06)

DELAY AUTOARMDELAY AUTOARM

DELAY AUTOARM

(07)(07)

(07)

1 2 3 4 5 6 7 8 9 10 11 12 ... 51 52

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC PC6010 Installationshandbuch Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC PC6010