DSC Power832 PC5O15 Installationshandbuch PDF herunterladen (Seite 15)

G E T T I N G S T A R T E D

2.10.8 LINKS Supervisory (24 Hour Supervisory)

When using the LINKS1000 cellular communicator, any main board zone may

be configured for LINKS Supervision. Program this zone as zone type [09], 24

Hour Supervisory in section [001].

With a 24 Hour Supervisory zone, if the LINKS1000 experiences a trouble, the zone

will be violated, causing the panel to report the event to the central station. This

type of zone

always

requires a single EOL resistor (5600Ω).

Wire this zone according to the diagram.

2.10.9 LINKS Answer

If the LINKS1000 cellular communicator is being used a zone may be

configured for LINKS Answer to allow downloading to be performed in the event

of phone line failure.

When the LINKS receives a phone call it will activate the RING terminal on the

LINKS circuit board. This terminal can be used to violate a zone programmed as

LINKS Answer

(See Section 5.1 “Zone Definitions”)

, causing the panel to seize the

phone line and begin communication with the downloading computer.

The zone programmed as LINKS Answer ALWAYS requires a single EOL resistor

(5600Ω) and must be wired according to this diagram.

The LINKS Answer zone is only rThe LINKS Answer zone is only r

The LINKS Answer zone is only r

equirequir

equir

ed for downloading to the panel via the LINKS. When using theed for downloading to the panel via the LINKS. When using the

ed for downloading to the panel via the LINKS. When using the

LINKS, Busy TLINKS, Busy T

LINKS, Busy T

one Detection must not be used. Keypad zones cannot be used for 24 Hour Superone Detection must not be used. Keypad zones cannot be used for 24 Hour Super

one Detection must not be used. Keypad zones cannot be used for 24 Hour Super

vi-vi-

vi-

sorsor

sor

y or LINKS Answery or LINKS Answer

y or LINKS Answer

2.11 Keypad Zones

Keypads with zone inputs can be connected to devices such as door contacts. This saves you from running wires back to

the control panel for every device.

To install the keypad, open the keypad plastic by removing the screw at the bottom of the unit. Locate the five terminals on

the keypad circuit board. Connect the four Keybus wires from the control panel: the red wire to R, the black to B, the yellow

to Y and the green to G.

To connect the zone, run one wire to the Z terminal and the other to B. For powered devices, use red and black to supply

power to the device. Run the red wire to the R (positive) terminal and the black wire to the B (negative) terminal. When

using end of line supervision, connect the zone according to one of the configurations outlined in Section 2.8 “Zone

Wiring.” End of line resistors must be placed on the device end of the loop, not at the keypad.

Keypad zones do not supporKeypad zones do not suppor

Keypad zones do not suppor

DEOL rDEOL r

DEOL r

esistors.esistors.

esistors.

Only non 24-hr burOnly non 24-hr bur

Only non 24-hr bur

glarglar

glar

y zonesy zones

y zones

can be configurcan be configur

can be configur

ed as keypaded as keypad

ed as keypad

zones for UL Listed przones for UL Listed pr

zones for UL Listed pr

oducts.oducts.

oducts.

Assigning Keypad Zones

When using keypad zone inputs, each input used must be assigned a zone number in Installer’s Programming.

First, ensure that you have enrolled all installed keypads into the desired addresses (

see section 2.6 ‘Keypad

Assignment’).

Next, enter programming section [020] to assign the zones. There are eight programming locations

in this section, one for each keypad address. Enter a 2-digit zone number for each of the keypad zones. This

number must be entered in the location corresponding to the keypad to which each zone is connected.

If a keypad zone input is assigned on zone number forIf a keypad zone input is assigned on zone number for

If a keypad zone input is assigned on zone number for

m 1 to 8, the corm 1 to 8, the cor

m 1 to 8, the cor

esponding zone cannot beesponding zone cannot be

esponding zone cannot be

used on the main contrused on the main contr

used on the main contr

ol panel. Once the keypad zones arol panel. Once the keypad zones ar

ol panel. Once the keypad zones ar

e assigned, you must also pre assigned, you must also pr

e assigned, you must also pr

ogram zoneogram zone

ogram zone

definitions and zone attributes (see also Section 5.1.1 ‘Assigning Keypad Zones’).definitions and zone attributes (see also Section 5.1.1 ‘Assigning Keypad Zones’).

definitions and zone attributes (see also Section 5.1.1 ‘Assigning Keypad Zones’).

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 47 48

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC Power832 PC5O15 Installationshandbuch Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC Power832 PC5O15