DSC Power832 PC5O15 Installationshandbuch PDF herunterladen (Seite 23)

How to Program

S E C T I O N 4

The following section of the manual describes how to enter Installer Programming and how to program the various

sections.

It is extrIt is extr

It is extr

emely imporemely impor

emely impor

tant that you rtant that you r

tant that you r

ead the following section of the manual to completely understand how toead the following section of the manual to completely understand how to

ead the following section of the manual to completely understand how to

prpr

ogram the panel.ogram the panel.

ogram the panel.

4.1 How to Enter Installer Programming

Installer Programming is used to program all communicator and panel options. The Installer Code is [5015] at

default but should be changed to prevent unauthorized access to programming.

Once the InstallerOnce the Installer

Once the Installer

’’

’

s Mode is exited, the system will rs Mode is exited, the system will r

s Mode is exited, the system will r

eset. This will take 15 seconds. Do not attempt toeset. This will take 15 seconds. Do not attempt to

eset. This will take 15 seconds. Do not attempt to

perper

per

forfor

for

m any system function during this rm any system function during this r

m any system function during this r

eset period. In addition, all outputs will reset period. In addition, all outputs will r

eset period. In addition, all outputs will r

eturetur

etur

n to theirn to their

n to their

nornor

nor

mal, deactivated state (or activated if invermal, deactivated state (or activated if inver

mal, deactivated state (or activated if inver

ted).ted).

ted).

LED Keypad or Fixed Message LCD Keypad:

Step 1 From any keypad enter [✱][8][Installer Code].

• The ‘Program’ light will flash to indicate you are in programming

• The ‘Armed’ light will turn on to indicate the panel is waiting for the 3 digit Section number to program

Step 2 Enter the 3 digit Section number you want to program.

• The Armed light will turn off

• The Ready light will turn on to indicate the panel is ready for the information for the selected Section

If the 3 digit section number enterIf the 3 digit section number enter

If the 3 digit section number enter

ed is not valid or the module that pered is not valid or the module that per

ed is not valid or the module that per

tains to the Section is nottains to the Section is not

tains to the Section is not

prpr

esent, the keypad will sound a 2 second beep or eresent, the keypad will sound a 2 second beep or er

esent, the keypad will sound a 2 second beep or er

or tone.or tone.

or tone.

LCD Keypad

Step 1 From any keypad enter [✱][8][Installer Code].

The Keypad will display ‘Enter Section’ followed by three dashes.

Step 2 Enter the 3 digit Section number you want to program.

The keypad will now display information for the section entered.

Installer Code .......................................................... Section [006]

4.2 Programming Decimal Data

When the Ready light is ON the panel is waiting for the information to be programmed for the selected Section.

Enter the information written in the boxes for the Section found in the Programming Worksheets.

If a digit is entered for each program box in a Section the panel will automatically exit from the Section. It will

turn OFF the Ready light and turn the Armed light back ON.

You can also press the [#] key to exit a Section before entering data for every box. This is handy if you only

need to change the first few program boxes. All other locations in the Section will remain unchanged. If the [#]

key is pressed the panel will turn OFF the Ready light, turn ON the Armed light and exit you from the Section.

4.3 Programming HEX Data

On occasion, hexadecimal (HEX) digits may be required. To program a HEX digit press the [✱] key. The panel

will enter HEX programming and Ready light will begin to flash.

The following table indicates which number should be pressed to enter the corresponding HEX digit:

1 = A 2 = B 3 = C 4 = D 5 = E 6 = F

After the correct HEX digit is entered the Ready light will continue to flash. If another HEX digit is required press

the corresponding number. If a decimal digit is required press the [✱] key again. The Ready light will turn on

solid and the panel will return to regular decimal programming.

It is imporIt is impor

It is impor

tant to watch the Ready light. If the light is flashing any number you enter will be prtant to watch the Ready light. If the light is flashing any number you enter will be pr

tant to watch the Ready light. If the light is flashing any number you enter will be pr

o-o-

grammed as the HEX equivalent.grammed as the HEX equivalent.

grammed as the HEX equivalent.

Example: To enter ‘C1’ for a closing by user 1, you would enter [✱] [3] [✱], [1]

[✱] to enter Hexadecimal mode (Ready light flashes)

[3] to enter C

[✱] to return to decimal mode (Ready light is solid)

[1] to enter digit 1

If you enter information into a section and make a mistake, press the [#] key to exit the section. Select that

section again and re-enter the information correctly.

If you are using a pulse communications format, a decimal zero [0] does not transmit. Programming a zero [0]

tells the panel not to send any pulses for that digit. Decimal zero [0] is a filler digit. To make a zero [0] transmit,

it must be programmed as a Hexadecimal ‘A’.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 47 48

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC Power832 PC5O15 Installationshandbuch Seite 23

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC Power832 PC5O15