DSC Power832 PC5O15 Installationshandbuch PDF herunterladen (Seite 41)

P R O G R A M D E S C R I P T I O N S

5.28.2 Factory Default Main Panel (Software) and other Modules

Step 1 - Enter Installer Programming.

Step 2 - Enter Program Section [99X].

Step 3 - Enter the Installer Code.

Step 4 - Enter Program Section [99X] again.

The panel will take a few seconds to reset. When the keypad is operational, the default is complete.

Restore Alternate Communicator to Factory Default Programming ... Section [993]

Restore Escort5580 to Factory Default Programming ......................... Section [995]

Restore PC5132 to Factory Default Programming .............................. Section [996]

Restore PC5400 to Factory Default Programming .............................. Section [997]

Restore PC5928/5936 to Factory Default Programming ...................... Section [998]

Restore Main Panel (Software) to Factory Default Programming ....... Section [999]

5.29 Installer Lockout

If Installer Lockout is selected a hardware default cannot be performed. If a software default is performed all

programming will restore to factory default.

When Installer Lockout Disable is selected the panel will restore all programming to factory defaults if a

hardware or software default is performed on the main control panel.

To enable or disable Installer Lockout perform the following:

Step 1 - Enter Installer Programming.

Step 2 - Enter Program Section [99X].

Step 3 - Enter the Installer Code.

Step 4 - Enter Program Section [99X] again.

Installer Lockout Enable ......................................... Section [990]

Installer Lockout Disable ........................................ Section [991]

5.30 Walk Test (Installer)

The Installer Walk Test can be used to test the alarm state of each zone of the panel. The walk test cannot be

used to test zone type [24].

Before beginning the walk test, ensure the following conditions are met:

1. The panel is disarmed

2. The Keypad Blanking option is disabled (section [016]: [3])

3. The Fire Bell is Continuous option is disabled (section [014]: [8])

4. The Transmission Delay is disabled, if Transmission Delay is not required (section [370])

FirFir

Fir

e Te T

e T

oubles aroubles ar

oubles ar

e not suppore not suppor

e not suppor

ted in Wted in W

ted in W

alk Talk T

alk T

est.est.

est.

All outputs will activate for both parAll outputs will activate for both par

All outputs will activate for both par

titions during the walk test, rtitions during the walk test, r

titions during the walk test, r

egaregar

egar

dless of prdless of pr

dless of pr

ogramming.ogramming.

ogramming.

To perform a Walk Test, do the following:

Step 1 - Enter Installer Programming

Step 2 - Enter Section [901]

When any zone is violated the panel will activate the Bell Output for two seconds, log the event to the Event

Buffer and communicate the alarm to central station. Each zone should be tested several times during the test.

Check the event buffer to ensure that all zones and FAP keys are functioning properly.

To stop the test, you must do the following:

Step 1 - Enter Installer Programming

Step 2 - Enter Section [901]

Zones do not have to be restored to stop the test. After the test is complete, check the Event Buffer to ensure

that the Audible/Silent 24-hr PGM alarms have been restored.

The AlarThe Alar

The Alar

m Memorm Memor

m Memor

y is cleary is clear

y is clear

ed upon entering Wed upon entering W

ed upon entering W

alk Talk T

alk T

est mode. When the West mode. When the W

est mode. When the W

alk Talk T

alk T

est is complete, theest is complete, the

est is complete, the

AlarAlar

Alar

m Memorm Memor

m Memor

y light will ry light will r

y light will r

emain lit, but theremain lit, but ther

emain lit, but ther

e will be no alare will be no alar

e will be no alar

ms in memorms in memor

ms in memor

. The light will tur. The light will tur

. The light will tur

n ofn of

n of

f thef the

f the

next time the panel is arnext time the panel is ar

next time the panel is ar

med.med.

med.

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 47 48

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC Power832 PC5O15 Installationshandbuch Seite 41

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC Power832 PC5O15