DSC Power832 PC5O15 Installationshandbuch PDF herunterladen (Seite 29)

P R O G R A M D E S C R I P T I O N S

26

Please refer to Appendix A: “Reporting Codes”for a list of Contact ID Identifiers.

Contact ID Uses Programmed/Automatic Codes .. [381]: [7]

5.6.3 SIA (Level 2)

SIA is a specialized format that will communicate information quickly using frequency shift keying (FSK) rather than

pulses. The SIA format will automatically generate the type of signal being transmitted, such as Burglary, Fire,

Panic etc. The two digit reporting code is used to identify the zone or access code number.

SIA forSIA for

SIA for

mat must be used if Downlook is rmat must be used if Downlook is r

mat must be used if Downlook is r

equirequir

equir

ed.ed.

ed.

If the SIA format is selected the panel can be programmed to automatically generate all zone and access codes

numbers eliminating the need to program these items.

If the SIA Sends Automatic Reporting Codes option is enabled the panel will operate as follows:

1. If the reporting code for an event is programmed as [00] the panel will not attempt to call the central station.

2. If the reporting code for an event is programmed as anything from [01] to [FF] the panel will AUTOMATICALLY

generate the zone or access code number.

3. Bypassed zones will always be identified when partial closing the system.

The Communicator Call Direction Options can be used to disable reporting of events such as Openings/Closings.

Also, if all the Opening/Closing reporting codes were programmed as [00] the panel would not report.

If the SIA Sends Automatic Reporting Codes option is disabled the panel will operate as follows:

1. If the reporting code for an event is programmed as [00] or [FF] the panel will not attempt to call central station.

2. If the reporting code for an event is programmed as anything from [01] to [FE] the panel will send the

programmed reporting code.

3. Bypassed zones will not be identified when partial closing the system.

Do not prDo not pr

Do not pr

ogram the second phone number for the SIA rogram the second phone number for the SIA r

ogram the second phone number for the SIA r

eporepor

epor

ting code forting code for

ting code for

mat (Section [360]) if themat (Section [360]) if the

mat (Section [360]) if the

Automatic ReporAutomatic Repor

Automatic Repor

ting Code option is enabled (Section [381]).ting Code option is enabled (Section [381]).

ting Code option is enabled (Section [381]).

Communicator Format ............................................ Section [360]

SIA Sends Automatic Reporting Codes ................ Section [381], Option [3]

Communicator Call Direction Options ................... Section [361] to [368]

SIA Identifiers ......................................................... Appendix B

5.6.4 Residential Dial

If Residential Dial is programmed and an event that is programmed to communicate occurs, the panel will seize

the line and dial the appropriate phone number(s). Once the dialing is complete, the panel will emit an ID tone

and wait for a handshake (press a 1, 2, 4, 5, 7, 8, 0, ✱ or # key from any phone). It will wait for this handshake

for the duration of Post Dial Wait for Handshake timer.

Once the panel receives the handshake, it will emit an

alarm tone over the phone line for 20 seconds. If several alarms occur at the same time, only one call will be

made to each phone number the panel is programmed to call.

Communicator Format Options .............................. Section [360]

Communicator Call Direction Options ................... Section [361] to [368]

5.6.5 Pager Format

The Communicator Format option for either phone number can be programmed for Pager Format. If an event

occurs and the Communicator Call Direction options direct the call to a phone number with the Pager Format

selected the panel will attempt to page.

When calling a pager extra digits will be required to make it work properly.

The following is a list of Hex digits and what function they perform:

Hex [B] - simulates the [✱] key on a touch tone phone Hex [E] - two second pause

Hex [C] - simulates the [#] key on a touch tone phone Hex [F] - end of phone number marker

Hex [D] - forces the panel to search for dial tone

The panel will attempt to call the pager one time. After dialing the digits in the phone number the panel will send

the account number and reporting code followed by the [#] key (Hex [C]).

There is no ringback when using Pager Format. The panel has no way of confirming if the pager was called

successfully; a failure to communicate trouble will only be generated once the maximum number of attempts has

been reached.

The Pager ForThe Pager For

The Pager For

mat cannot be used with the LINKS1000 cellular communicatormat cannot be used with the LINKS1000 cellular communicator

mat cannot be used with the LINKS1000 cellular communicator

..

.

Do not use the digit C in a rDo not use the digit C in a r

Do not use the digit C in a r

eporepor

epor

ting code when using Pager Forting code when using Pager For

ting code when using Pager For

mat. In most cases, the digit C will bemat. In most cases, the digit C will be

mat. In most cases, the digit C will be

interprinterpr

interpr

eted as a [#], which will tereted as a [#], which will ter

eted as a [#], which will ter

minate the page beforminate the page befor

minate the page befor

e it has finished.e it has finished.

e it has finished.

If the panel detects a busy signal, it will attempt to page again. It will make the maximum number ofIf the panel detects a busy signal, it will attempt to page again. It will make the maximum number of

If the panel detects a busy signal, it will attempt to page again. It will make the maximum number of

attempts prattempts pr

attempts pr

ogrammed in section [160]. Forogrammed in section [160]. For

ogrammed in section [160]. For

ce dialing should be disabled when using Pager force dialing should be disabled when using Pager for

ce dialing should be disabled when using Pager for

mat.mat.

mat.

When using Pager forWhen using Pager for

When using Pager for

mat, you must prmat, you must pr

mat, you must pr

ogram two hex digit E’ogram two hex digit E’

ogram two hex digit E’

s at the end of the phone numbers at the end of the phone number

s at the end of the phone number

..

.

DSC Power832 PC5O15 Installationshandbuch Seite 29

Kommentare zu diesen Handbüchern

DSC Power832 PC5O15 Installationshandbuch Seite 29

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC Power832 PC5O15