DSC PC6010 Installationshandbuch Seite 14
- Seite / 52
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
12
SYSTEM AREASYSTEM AREA
SYSTEM AREASYSTEM AREA
SYSTEM AREA
COMMUNICATORCOMMUNICATOR
COMMUNICATORCOMMUNICATOR
COMMUNICATOR
COMMS TOGGLESCOMMS TOGGLES
COMMS TOGGLESCOMMS TOGGLES
COMMS TOGGLES
Communicator Toggles
Select options relevant to the telephone line communications of the panel. Toggle options are given in
the form of a question. Use the [*] key to toggle between [Y]es and [N]o to enable or disable the feature.
Use the [<][>] keys to scroll through the options.
Communications are enabled?
YES = The communications function is enabled.
NO = The communications function is disabled. No reporting codes will be transmitted to the central
station. Downloading using DLS-3 software will work with the communicator disabled.
DTMF dialing enabled?
YES = The dialer will use DTMF dialing.
NO = The dialer will use pulse dialing.
Partial Closings Identified?
YES = When using SIA, and when a zone is bypassed, unbypasssed, disabled, or enabled, the panel will
log and transmit the appropriate SIA identifier for the event, along with the zone alarm reporting
code. This will occur whether the zone was bypassed, unpassed, disabled, or enabled manually, or
automatically when the panel is armed or disarmed. The partial closing reporting code must be
programmed for this feature to work.
NO = The panel will only send the partial closing reporting code when zones are bypassed, unbypassed,
disabled, or enabled when the area is armed. However, it will still identify the zones in the event
buffer.
NOTE: If Partial Closings are used to identify alarms or restorals, the Alarm or Restoral reporting code
must be programmed for the feature to function properly.
Partial Closings on Auto Arming?
YES = The panel will send the partial closing reporting code to the central station when a zone is force
armed (temporarily bypassed) by an auto arm. If the option “PC ID” is enabled, and if the panel is
programmed to transmit using SIA, the force armed zone will be identified by sending the bypass
identifier and the zone alarm reporting code after the partial closing reporting code. See the
“Zone Operation” section in the System Manual for more information on force arming.
NO = No partial closing reporting code will be sent when zones are force armed during auto arming.
Telephone Line Monitoring Enabled?
YES = The system tests for telephone line faults. If a fault is detected, the trouble is annunciated on the
keypads. A telephone line trouble is generated when the line voltage drops below 3 volts for more
than 30 seconds.
NO = Does not test for telephone line faults.
Telephone Line Monitoring has Audible Bell Alarm?
YES = If there is a Telephone Line trouble and an area is armed, the bell outputs for the armed area will
be activated, along with the keypad annunciation. The bell outputs are any outputs (Bell, SW Aux
or PGM) programmed for “FIRE AND BURG”, “INV FIRE/ BURG”, “BURG ONLY” and “INV BURG
ONLY”.
NO = If there is a Telephone Line trouble, the panel will annunciate the trouble at the keypad only.
Should a Failure to Communicate sound the Bells?
YES = If an area is armed, the bell outputs for the armed area will sound when the PC6010 fails to
communicate with the central station.
NO = A failure to communicate will not cause the PC6010 to sound the bells.
Enable Ringback?
YES = The Ringback option is enabled. A successful communication of a closing to the central station will
be annunciated by the keypads beeping 5 times. Only the keypads belonging to the area that sent
the communication will beep.
If communications are being sent to more than one telephone number, keypads will sound the
ringback after the event(s) have been successfully communicated to each telephone number.
NO = The Ringback option is disabled.
NOTE: Ringback must be enabled on a commercial burglar alarm system.
COMMS TOGGLESCOMMS TOGGLES
COMMS TOGGLESCOMMS TOGGLES
COMMS TOGGLES
(1)(1)
(1)(1)
(1)
DTMF DIALINGDTMF DIALING
DTMF DIALINGDTMF DIALING
DTMF DIALING
YY
YY
Y
COMMS ENABLEDCOMMS ENABLED
COMMS ENABLEDCOMMS ENABLED
COMMS ENABLED
YY
YY
Y
PC IDPC ID
PC IDPC ID
PC ID
NN
NN
N
PC ON AUTO ARMPC ON AUTO ARM
PC ON AUTO ARMPC ON AUTO ARM
PC ON AUTO ARM
YY
YY
Y
TLM ENABLEDTLM ENABLED
TLM ENABLEDTLM ENABLED
TLM ENABLED
YY
YY
Y
TLM AUD BELLTLM AUD BELL
TLM AUD BELLTLM AUD BELL
TLM AUD BELL
YY
YY
Y
FTC AUD BELLFTC AUD BELL
FTC AUD BELLFTC AUD BELL
FTC AUD BELL
NN
NN
N
RINGBACKRINGBACK
RINGBACKRINGBACK
RINGBACK
NN
NN
N
- Programming Manual 1
- Introduction 3
- Main Programming Sections 4
- Installer Options 5
- System Options 6
- Keypad Lockout Options 7
- System Times 7
- Arm/Disarm Mask 8
- Zone Supervision 8
- Download Section 9
- Other DLS Programming 10
- Communicator Section 11
- SIA 1986 Format 12
- Contact ID 12
- Communicator Toggles 14
- Communicator Miscellaneous 16
- Test Code Transmission 16
- Reporting Codes 17
- Links Module 22
- Switched Auxiliary Output 23
- Main Bell Output 23
- PGM Outputs 24
- PGM Pulse Times 25
- Programmable Output Options 26
- Event Scheduling 30
- PC6820 Options 35
- Area Section 39
- Area Times 40
- Zone Assignment 41
- Zone Type 42
- Zone Options 44
- Alarm and Seismic Groups 45
- Area Label 45
- Delete/Copy Area 45
- Backbone Section 46
- Module Hardware 47
- Event Buffer 48
- Diagnostics 48
- Appendix A 49
- Appendix B 50
- Table 2: 51
- Zone Reporting Codes 51
- Toronto, Canada 52
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC PC6010
(56 Seiten)
(16 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.390 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern