DSC PC6010 Installationshandbuch PDF herunterladen (Seite 50)

Appendix B

Reporting Codes

Notes on Contact ID

The following is a list of Contact ID reporting codes. The first

digit (in parentheses) will automatically be sent by the control.

The last two digits are programmed to indicate specific

information about the signal.

For example, if zone 1 is an entry/exit point, the alarm reporting

code could be programmed as [34]. The central station would

receive the following:

*BURG - ENTRY/EXIT - 1

In the above example, the “1” indicates the zone in alarm.

Notes on SIA Format

If the SIA 1 Account # option is selected, the panel will send

the system account code along with its data transmission (ref #

[000401], scroll to option). At the receiver, the transmission

would look similar to this example:

N Ri01 / BA 001

N = New Event

Ri01 = Partition /Area Identifier

BA = Burglary Alarm

001 = Zone 1

Table 1:

Reporting Codes

Reporting Code Code Sent When...

Dialer

Direction*

Recommended

Contact ID

SIA Auto Rep

Codes**

Zone Alarms zone goes into alarm A/R

see Table 2 “Zone Reporting Codes”

Zone Restorals alarm condition has been restored A/R

Zone Trouble/Tamper zone exhibits a trouble/tamper condition A/R

Zone Trouble/Tamper Rest. trouble/tamper condition has cleared A/R

Zone Fault zone exhibits a zone fault A/R

Zone Fault Rest. zone fault condition has cleared A/R

Module Tamper Alarm/Rest.

enrolled module has a tamper alarm/tamper is

restored

A/R (1) 45 TA-000/TR-000

Closings area armed (user 001-128 indicated) O/C (4) A2 CL-UUU

Closing 129-1000 user code # 129-1000 used to arm partition O/C (4) A2 CL-UUU

Partial Closing

one or more zones intentionally bypassed

when area armed

O/C (4) 56 CW-000

Automatic (Scheduled) Closing auto arming according to schedule O/C (4) A3 CA-000

Auto Arm Cancellation auto arm cancelled O/C (4) A5 CE-000

6442 APS Closing area armed by APS software O/C (4) A2 CL-000

6443 ODS Closing area armed by ODS software O/C (4) A2 CL-000

Keypad Lockout

max. number of incorrect access codes has been

entered at a keypad

Other (4) 21 JA-000

Openings area disarmed (user 001-128 indicated) O/C (4) A2 OP-UUU

Opening 129-1000 user code # 129-1000 used to disarm area O/C (4) A2 OP-UUU

Opening After Alarm area disarmed with alarm in memory O/C (4) A6 OR-000

Automatic (Scheduled) Opening auto disarming according to schedule O/C (4) A3 OA-000

6442 APS Opening area disarmed by APS software O/C (4) A2 OP-000

6443 ODS Opening area disarmed by ODS software O/C (4) A2 OP-000

Battery Trouble/Rest. PC6010 battery is low Other (3) A2 YT-000/YR-000

AC Line Trouble/Rest.

AC power to control panel is disconnected or

interrupted

Other (3) A1 AT-000/AR-000

Main Bell Trouble/Rest. open circuit detected across bell terminals Other (3) 21 YA-000/YH-000

Main Auxiliary Trouble/Rest. aux voltage supply trouble Other (3) AA YP-000/YQ-000

Combus Fault/Rest.

control panel loses communications with

connected module(s)

Other (3) 33 ET-000/ER-000

Combus Low Power/Rest.

a module connected to the Combus has low

power

Other (3) 33 ET-000/ER-000

Backbone Trouble/Rest.

control panel loses communications with

connected backbone module(s)

Other (3) 33 ET-000/ER-000

TLM Failure/Rest.

telephone line monitoring trouble (sent via

LINKS or when land line communications

resume)

Other (3) 51 LT-000/LR-000

FTC Restoral

control panel has restored communications to

central station (after TLM Fail)

Other (3) 54 YK-000

* A/R = alarms/restorals; O/C = openings/closings

** PPP = partition number; UUU = user number (user 1000=999); ZZZ = zone number

1 2 ... 45 46 47 48 49 50 51 52

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC PC6010 Installationshandbuch Seite 50

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC PC6010