DSC PC6010 Installationshandbuch PDF herunterladen (Seite 8)

The system uses the Public key, together with the programmed Private key, to encrypt communications

over the Combus, making them more secure. The Public key is generated randomly by the system.

Program how often the system changes the Public key. Valid entries are from 000-255 minutes. The

default is 020 minutes. See also “Private Key” under Installer Options.

Program the dates on which Daylight Savings time begins. You can program the dates for up to three

years. Program the dates in the YY/MM/DD format. At 0200 on the programmed day, the time will

automatically move ahead one hour to 0300. The default dates that are programmed are 00/03/26, 01/

03/25, and 02/03/31.

NOTE: All scheduled events that would have occurred during the hours of 0200 to 0300 will not

occur on these days.

Program the dates on which Standard time begins. You can program the dates for up to three years.

Program the dates in the YY/MM/DD format. At 0300 on the programmed day, the time will automatically

move back one hour to 0200). The default dates that are programmed are 00/10/29, 01/10/28, and 02/

10/27.

Arm/Disarm Mask

All areas are toggled to YES, by default. Areas toggled to NO in the mask cannot be armed from a

keypad. Areas toggled to NO can only be armed by automatic arming, keyswitch arming, over the infranet,

or via the DLS-3 software. The default is YES for all areas. Only areas which have been added to the system

can be programmed in the Arm/Disarm Mask. See “Area Section” programming.

Zone Supervision

The zone is a normally closed loop to ground. The zone will be violated when it is open.

All zones must have a 5600 ohm resistor across them. If the zone is shorted or open, it will be in a

violated condition. If the zone is open and programmed as a fire zone, it will be in a trouble condition.

NOTE: If zones are programmed for Fire or Links Supervisory, EOL resistors must be used.

This configuration will allow the panel to detect zone Faults (zone loop is shorted), zone tampers (zone

loop is open), open zones (alarm condition 11200 Ohms) and restored zones (5600 Ohms). If the zone is

disarmed and placed in the Tamper or Fault state, the keypad buzzer will sound from all partition keypads

(that the zone belongs to) for the length of Bell Time out or until the alarm is silenced (by user code or

Keyswitch zone). A zone trouble reporting code will be sent to the monitoring station (if programmed).

When the partition is armed and a zone is Tampered or Faulted, the keypad buzzer will sound from all

partition keypads (that the zone belongs to) for the length of Bell Time out or until the alarm is silenced,

but no burglary outputs will be activated and only the Trouble reporting code will be transmitted to the

monitoring station (if programmed). Refer to the System Manual for details on the hookup procedure.

All zones on the PC6010 can use Double End of Line resistors except Fire Zones (all types - Standard Fire

and Auto Verify Fire), Links Supervisory, and Links Answer zone types. These zones must only use Single

EOL.

ARM/DISARM MASKARM/DISARM MASK

ARM/DISARM MASK

(3)(3)

(3)

PUBLIC KEY CYCLEPUBLIC KEY CYCLE

PUBLIC KEY CYCLE

(08)(08)

(08)

SYSTEM AREASYSTEM AREA

SYSTEM AREA

SYSTEM OPTIONSSYSTEM OPTIONS

SYSTEM OPTIONS

SYSTEM TIMESSYSTEM TIMES

SYSTEM TIMES

SYSTEM AREASYSTEM AREA

SYSTEM AREA

SYSTEM OPTIONSSYSTEM OPTIONS

SYSTEM OPTIONS

ARM/DISARM MASKARM/DISARM MASK

ARM/DISARM MASK

DAYLIGHT SAVINGSDAYLIGHT SAVINGS

DAYLIGHT SAVINGS

(09)(09)

(09)

STANDARD TIMESTANDARD TIME

STANDARD TIME

(10)(10)

(10)

ZONE SUPERVISIONZONE SUPERVISION

ZONE SUPERVISION

(4)(4)

(4)

NO EOLNO EOL

NO EOL

SINGLE EOLSINGLE EOL

SINGLE EOL

DOUBLE EOLDOUBLE EOL

DOUBLE EOL

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 51 52

Kommentare zu diesen Handbüchern

Keine Kommentare

DSC PC6010 Installationshandbuch Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme DSC PC6010